Peel-and-Stick Brick Backsplash in an RV (What Worked, What Didn’t, and How I Hid the Seams)

A real-life RV kitchen upgrade using foam-backed peel-and-stick brick tile — including seam issues, the almond “grout” fix, and why patience mattered more than perfection.

Finished peel and stick brick backsplash in an RV kitchen with almond grout and no visible seams

I chose peel-and-stick tile for our RV kitchen because it just makes sense for full-time RV living. It’s lightweight, budget-friendly, and flexible enough to handle the vibrations of travel — plus there are so many styles to choose from. I landed on a brick pattern because I’m all about that cozy, country-cottage feel. If I’m going to live in an RV full time, it has to feel like home — no exceptions. And in the end, it was absolutely worth it.


How I Installed the Peel-and-Stick Brick Backsplash

1. Prep the Wall

I started by thoroughly cleaning the wall to make sure the adhesive would stick properly. First, I cleaned the area with diluted Simple Green, followed by a light rinse. Once dry, I wiped everything down with 90% rubbing alcohol using a clean cloth and let it air dry for about 20 minutes. This step is important — any grease or residue can cause adhesion issues later.

2. Dry Fit (No Measuring Required)

Before removing any backing, I dry-fit each panel. Because these tiles have a foam backing, I didn’t need to measure. Instead, I pressed the panel firmly into place along the window edge to create an impression on the back of the foam. That impression gave me a perfect cut line. I trimmed the panels using sharp scissors.

3. Apply Adhesive & Install

Once trimmed, I peeled off the backing and brushed on a coat of Zinsser SureGrip 122 heavy-duty wallcovering adhesive. I then set the panel in place and repeated the process for each section:

  • Dry fit
  • Create impression
  • Cut
  • Peel backing
  • Apply adhesive
  • Press into place

For small exposed areas left by the pre-cut panels, I cut brick pieces from leftover scraps and installed them the same way until the wall was fully covered.

Brushing wallcovering adhesive onto the back of peel-and-stick brick tile during RV backsplash installation

4. Secure the Seams

The panels were just heavy enough that some sections wanted to slide or lift slightly. To keep everything in place, I used painter’s tape to hold down the seams while the adhesive cured. I left the tile taped and undisturbed for about two days.

Painter’s tape holding peel-and-stick brick tile seams in place during RV backsplash installation

5. Fix Raised Edges (Before Grouting)

Before adding grout, I checked for any raised edges. In a few spots where the adhesive had dried unevenly, I added a bit more glue behind the tile and held it flat using a push pin placed directly into the raised brick area. This kept everything flush and out of the way for grouting.

6. Grouting the Seams

For grout, I used Dynaflex 230 Almond elastomeric caulk. Working in small sections, I applied the caulk with a caulk gun, then smoothed it using the back of a spoon. Any excess caulk on the spoon was pressed into nearby channels so nothing went to waste. I wiped the spoon clean frequently with a paper towel to prevent dried buildup.

After completing one or two sections, I waited a minute or two for the caulk to begin setting. Then I used a small, slightly damp piece of grout sponge to add texture using gentle pats and feather-light swipes. I rinsed and wrung out the sponge often — keeping it damp, not wet — so the caulk’s integrity wasn’t compromised.

Applying almond-colored caulk to peel-and-stick brick backsplash seams in an RV kitchen
Texturing almond caulk grout with a damp sponge on peel-and-stick brick backsplash

7. Final Cleanup & Sealing

Once I was happy with the texture, I lightly cleaned excess caulk from the raised brick areas — but not too much. Leaving a bit of overlap along the edges makes the brick look more natural and realistic (my personal preference).

After the entire backsplash was finished, I used a scrubby sponge to clean any caulk from the countertops, walls, and window trim. The final step was sealing all outer edges — where the tile meets the window and walls — with clear caulk for a finished look.

The next day, I removed the push pins, and the backsplash was fully set, secure, and finished — and beautiful.

Cleaning excess caulk around RV kitchen window trim after grouting peel-and-stick brick tile

Supplies & Tools Used

(This post contains affiliate links. As an Amazon Associate, I earn from qualifying purchases.)

🧱 Tile & Adhesives

🧼 Surface Prep

  • Simple Green (or similar degreasing cleaner)
  • 90% isopropyl rubbing alcohol
  • Clean lint-free cloths or paper towels

✂️ Cutting & Installation Tools

🧂 Grout & Finishing

🧽 Cleanup

  • Scrubby sponge
  • Bucket or bowl of clean water

Lessons Learned Along the Way

  • Foam-backed peel-and-stick tiles are heavier than they look, and some sections will want to lift or slide while drying.
  • Painter’s tape helps, but in a few areas it wasn’t strong enough on its own.
  • Using push pins together with painter’s tape worked extremely well for holding stubborn seams flat while the adhesive cured.
  • Dry fitting the panels and pressing them in place to create cut impressions saved time and eliminated measuring errors.
  • A spoon worked better than a trowel for smoothing soft caulk without digging it out of the seams.
  • Letting the caulk set for a minute or two before adding texture made it much easier to work with.
  • Slight imperfections in the grout lines actually add to the realistic brick look.

Looking back, these small adjustments made all the difference.


Would I Do This Again?

I’m not a professional contractor — but I have tackled many renovation projects in my own home over the years. This one was new territory for me, especially doing it inside an RV, where weight, movement, and flexibility all matter. The process is definitely different from a traditional home install.

That said, hindsight is everything. There are a few things I would approach differently next time, but that only became clear after stepping back and seeing the finished project. Overall, this install was straightforward, not overly time-consuming, and very manageable for a beginner DIYer.

Knowing what I know now, I would absolutely do this again. In fact, I’m already considering using this same tile and grout technique on the bathroom walls. I love the texture of the brick, and the finished grout look gives the space so much warmth and character.


Let’s Talk DIY RV Projects

Have you tackled a backsplash or wall project in your RV? I’d love to hear about it.
Drop a comment below with your experience, any tips you’d share, or even a photo of your finished project. Every RV is a little different, and shared advice is always appreciated.

Leave a Reply


💛 Stay Cozy with Nourish-Nest

New recipes, tiny-kitchen tips, cookie drops, and a dash of sarcasm.

📘 Facebook 📸 Instagram 📌 Pinterest 📺 YouTube 🎵 TikTok
Sherryl Jenkins Avatar

Published by

© 2025 Nourish-Nest Blog — Recipes and photos may not be reproduced or redistributed without written permission.

Leave a Reply